Re: eigenvalues

On Thu, Nov 05, 2015 at 05:14 PM, Jeroen Elassaiss-Schaap (PD-value B.V.) wrote: Hi Pavel, Principal component analysis can be validly performed on any matrix, and it is just a matter of convention that the eigenvalue ratios of min/max of the total covariance matrix of estimation are reported as the condition number for a given model. This as a metric of how easily the dimensionality of estimators could be reduced. The idea behind the separation of eigenvalues, as you show here for your model in Monolix, is actually attractive, because the off-diagonal elements do reduce the freedom of the described variance rather than increasing it. Furthermore they are the byproduct of sampling methods like SAEM, not so much the result of separate estimation. Two reasons to separate them. The separation of diagonal variance components and PK parameters as you note is less obvious to me, although I am pretty sure there will be a good rationale for that in the realm of sampling approaches (tighter linkage?). Even though the off-diagonal elements are associated with a decent condition number, it is still larger than the "PK" block, assuming the blocks are of comparable size. In other to better compare the results my suggestion would be to break up the nonmem covariance matrix (as was done for Monolix) in blocks of structural, diagonal and off-diagonal elements (throwing away a large remainder), and calculate the condition number on each matrix. Than you are comparing apples to apples, enabling a more straightforward discussion of the differences. Hope this helps, Jeroen http://pd-value.com http://pd-value.com [email protected] <mailto:[email protected]> @PD_value +31 6 23118438 -- More value out of your data! On 11/04/2015 05:55 PM, Pavel Belo wrote: Hello NONMEM Users, I try to make sense of the results and one of the ways to do it is to compare the same or similar models across software packages. 5x5 full omega matrix is used because it was prohibitive to remove some insignificant correlations from the matrix without removing significant correlations (All recommended ways to do it were tested. Diagonal omega was also tested, of course). Adding correlations has little effect on PK parameters, but it has some effect on simulations. NONMEM provides all eigenvalues in one pocket. Here is an example. ************************************************************************************************************************ ******************** ******************** ******************** STOCHASTIC APPROXIMATION EXPECTATION-MAXIMIZATION ******************** ******************** EIGENVALUES OF COR MATRIX OF ESTIMATE (S) ******************** ******************** ******************** ************************************************************************************************************************ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 3.36E-05 5.69E-03 3.40E-02 6.32E-02 9.19E-02 1.24E-01 1.53E-01 2.79E-01 3.20E-01 4.32E-01 5.74E-01 6.45E-01 7.25E-01 7.67E-01 9.73E-01 1.08E+00 1.42E+00 1.63E+00 1.86E+00 2.14E+00 2.31E+00 3.12E+00 4.26E+00 Monolix provides them in 3 pockets: PK parameters: Eigenvalues (min, max, max/min): 0.22 2 9.2 OMEGA (diagonal) and SIGMA: Eigenvalues (min, max, max/min): 0.66 1.5 2.2 OMEGA (correlations): Eigenvalues (min, max, max/min): 0.097 2.5 25 Even though the results look similar, eigenvalues look different. Taking into account that max/min ratio is frequently reported, it is important to understand the difference. It almost look like different sets of parameters are estimated separately in the Monolix example, which most likely is not the case. Even if we combine all eigenvalues in one pocket, max/min looks good. It is impressive that max/min ratio for OMEGA correlations may look OK even though there are small correlations such as -0.0921, SE=0.064, RSE=70%. What is the best way to report estimate and report max/min ratios? Take care, Pavel